The EP Series Helical Bevel Reducer provides unmatched performance, durability, and design flexibility. This unit provides torque capacities up to 20,000 Nm (14,750 ft pounds).
The cat4CAD software allows simple interactive product selection of the entire gearbox and gear-electric motor system. Cat4CAD facilitates you in selecting and configuring these products, provides you the opportunity to print out intensive technical data bedding, and generates complete 2D drawings and 3D models for direct download.
11 sizes
Insight power capacities from 0.16 to 120 HP
Gear ratios from 5:1 to 8900:1
Torque capacities to 20,000 Nm
Inverter duty course F insulated motor windings
Class 12 Helical and Spiral Bevel Gears: Provides higher efficiencies and better torques in smaller sizes.
Multiple Input Options: Integral gear motors, in . or metric shafts, NEMA, IEC, and servo adapters provide unmatched drive versatility.
Multiple Output Choices: Hollow bores and shrink disks for shaft mounting, inch and metric result shafts, installation pilots and flanges offer a wide variety of design solutions.
UNIBLOCK Housing: For optimum rigidity, universal helical bevel gear reducer mounting on five sides or with a torque arm.
Worldwide Motor: Multiple leads and windings for globally multi volt/Hz requirements in addition modular design to accept brakes, encoders or pressured cooling.
High efficiency motor design available
Innovative self-locking, self-aligning taper shaft electric motor connection
Gearbox supplied factory filled with synthetic oil
Corrosion and shock resistant cast iron housing
High efficiency helical-bevel gears. 98% per stage
Normally closed breather with multiple locations (Optional OtN2000)
Double lip seals upon heat treated, plunge ground shafts
Shaft mounting choices include tapered bushings designs
This is a comprehensive offering of energy-efficient, right angle helical bevel enclosed gearing. It is obtainable as gearmotors and a number of reducers with torque capacities up to 119,000 inch pounds. Housing designs include footed, encounter and flanged configurations. Gearmotors are available in three stage high efficiency designs through 50 HP and single phase to 5 HP. We provide a selection of input and result shaft options. Additionally, you will see fixed and variable acceleration motors and selection of ratios obtainable in this product offering.
Features
Accommodates input power from ¼ Hp to 75Hp
Torque ratings up to 119,489 in-lbs
Reduction ratios up to 7,500:1
Helical – bevel – helical gear train offers cost effective high and low speed solutions
Up to 94% efficient
Four input options available for all units
Two output flange choices – B5 and B14
Multiple output shaft interfaces
Critical dimensions interchangeable with major competitors
Modifications / Accessories
Integral Gearmotor
Clamp Collar C-Face Input
Solid Shaft Input
3-Piece Coupled C-Face Input
CEMA Screw Conveyor Adapter
EZ Kleen Washdown Package
XT Output Seals
Backstop
DURABLE Output Bearings
Inch or Metric Dimensions
Common Applications
Troughing Belt Conveyors
Slider Bed Conveyors
Mixer Drives
Screw Conveyors
Bucket Elevators
General Industrial Machinery
Common Industries
Aggregate and Cement
Air Handling
Chemical, Oil, and Gas
Food, Beverage, and Pharmaceutical
Paper and Forest
Unit and Baggage Handling
Water and Wastewater
As per the growing and varying demands of customers, we offer an array of Helical Bevel Gear Reducers. The technological content of our products permits an extraordinary performance/lifespan ratio. The extremely versatile Helical Bevel Gear Reducers we offer are successfully used in a vast number of commercial and civil applications. These are B-Series units which offer excellent affordability and result torque/weight ratio, especially considering that they need very limited servicing. Besides these, our products can be found in cast iron (sizes 063 to 163) or light weight aluminum (sizes A42 to A73) casing.
Features:
Sizes: 060-080-100-125-140-150-160
Available versions: B-fitted for engine coupling, IB with input shaft, CB with small motor, PB-fitted for electric motor coupling with flexible joint
Casing with ft FC, flange SC and general UC
Power up to 90 kW
Gears hardened and tempered with shaved or surface profile
Gearing with 3 reduction stages
Gleason spiral bevel equipment pairs with run-in profile, mounted as second reduction stage for a higher resistance
Reduction ratios between 5, 71 and 187, 24
Torque max 13.000 Nm and admissible radial loads max 80.000 N
High-strength casings optimized with FEM evaluation and input and output flanges of grey cast-iron G200 to make sure top level performances and high reliability
Load capacity calculated and verified according to ISO 6336 and AGMA 2001
Painted with RAL 5010 blue epoxy-polyester powder
Accessories: torque arm, result flange, result shaft, shrink disk, backstop device, protection cover package, viton essential oil seals, reinforced output, assemble/disassemble kit
Series EP right position helical bevel equipment motors provide ratios from 8:1 to 160:1 in three levels or up to 10000:1 in five phases. Motors are available up to 90kW and output torque capability up to 12,300 Nm.
The series EP helical bevel gear motor was created with integral cast feet for base or end mounting and may be offered with single or dual extended output shafts.
Systems are also available as shaft mounted or with result flanges and are designed for mounting horizontally or vertically. The devices can also be offered with a bolt on torque response bracket and all variants are available either motorised or with an insight shaft assembly.
Adding to the brand new range of Ever-Power helical gear motors the product takes advantage of our many years of accumulated design expertise together with the use of high quality materials and elements. The outcome is a number of rate reducing geared motors providing high load holding capacities, increased efficiency, peaceful running and reliability.
Top features of Helical Bevel Gear Motor
Standard motor connection
Capability to fit double essential oil seals, on insight and output shaft as required.
All models are dimensionally interchangeable with various other major manufacturers.
Units are produced and assembled from a family of modular kits for distributor friendliness minimizing inventory and maximizing availability.
Motorized units could be fitted with a backstop module and reducer Products can be fitted with a backstop and fan.
Applications:
-Conveyors, Agitators, Elevators, Cranes, Crushers
-Helical Bevel gear motors are found in industries such as chemical substances, pharma, packaging, food processing, plastic-type and automation etc.
Key Features:
Sizes: A40-A50-A70
Obtainable versions: EP – fitted for engine coupling, IEP – with input shaft, CEP – with small motor
Cases with ft, flange or universal
Power up to 4,8 Kw
Gears with shaved or surface profile
Gearing with 2 and 3 reduction stages
Hypoid bevel gears for size A40 and A50, gleason bevel gear pairs for size A70, all with run-in profile
Reduction ratios between 7,62 and 442,76
Torque max 450 Nm and admissible radial loads max 5.500 N on hollow shaft and 10.000 N on solid shaft
Cases in die-cast aluminium alloy
Exceptional mechanical strength while being and particularly lightweight
Load capacity calculated to ISO6336 and verified according to AGMA 2001-B88
Painted with RAL 5010 blue epoxy-polyester powder in according to DIN 1843
Accessories: torque arm, output flange, output shaft.
Generallntroduction of HK series:
Gear Reducer
The EP series gear units, are novel transmission device and made up of Y series engine, helical gear,Arc gear and worm gear. The gears are made of high wear-resisting alloy materials, specially and finely processed.
Advantages:
1: Helical-bevel equipment two-stage reducer
2: Compact structure, high efficiency
3: Quenched 20CrMnTi for gears
4: CE, ISO9001.
5: Small design, small volume, nice appearance ,and solid capacity to be overloaded.
6: Precise division and wide selection for transmission ratio.
7: The effectiveness is up to as high since 96% with low energy intake, strong adaptability and is with the capacity of functioning continually in corrosive or damp environment.
8: All- purpose make use of, convenient and low-price maintenance.
9: New seal device, strong adaptability.
10: Varied selection of motor combinations, mouting positions and struture projects.