梅花形弹性联轴器主要适用于起动频繁、正反转、中高速、中等扭矩和要求高可靠性的工作场合,例如:冶金、矿山、石油、化工、起重、运输、轻工、纺织、水泵、风机等。公称转矩为25~12500N.m,许用转速为15300~1900r/min,轴孔直径为12~160mm。
Basic parameters and main dimensions of LM (formerly ML) basic plum-shaped elastic coupling (GB/T 5272-2002) (unit: mm)
model | Old model | Nominal torque/Nm | Allowable speed/r/min | Diameter of shaft hole d1,d2,dz | L | Lo | D | Elastic part model | Weight/kg | Moment of inertia/kg.㎡ | |
Elastic part hardness | |||||||||||
a/Ha | b/Hb | ||||||||||
80 + 5 | 60 + 5 | ||||||||||
LM1 | ML1 | 25 | 45 | 15300 | 12,14 | 35 | 86 | 50 | MT1 | 0.657 | 0.00022 |
LM2 | 无 | 50 | 100 | 12000 | 16,18,19 | 38 | 95 | 90 | MT2 | 0.923 | 0.00044 |
LM3 | ML2 | 100 | 200 | 10900 | 20,22,24 | 40 | 103 | 70 | MT3 | 1.407 | 0.00087 |
LM4 | ML3 | 140 | 280 | 9000 | 22,24 | 45 | 114 | 85 | MT4 | 2.182 | 0.002 |
LM5 | ML4 | 350 | 400 | 7300 | 25,28 | 50 | 127 | 105 | MT5 | 3.601 | 0.0049 |
LM6 | ML5 | 400 | 710 | 6100 | 30,32,35,38, 40,42,45,48 | 55 | 143 | 125 | MT6 | 6.075 | 0.0114 |
LM7 | ML6 | 630 | 1120 | 5300 | 35*,38*,40*,42*,45,48,50,55 | 60 | 159 | 145 | MT7 | 9.089 | 0.0232 |
LM8 | ML7 | 1120 | 2240 | 4500 | 45*,48*,50,55,56 | 70 | 181 | 170 | MT8 | 13.561 | 0.0468 |
LM9 | ML8 | 1800 | 3550 | 3800 | 50*,55*,56*,60,63,65,70,71,75,80 | 80 | 208 | 200 | MT9 | 21.402 | 0.1041 |
LM10 | ML9 | 2800 | 5600 | 3300 | 60*,63,65*,70,71,75,80,85,90,95,100 | 90 | 230 | 230 | MT10 | 32.03 | 0.2105 |
LM11 | ML10 | 4500 | 9000 | 2900 | 70*,71*,75,80*,85*,90,95,100,110,120 | 100 | 260 | 260 | MT11 | 49.515 | 0.4338 |
LM12 | ML11 | 6300 | 12500 | 2500 | 80*,85*,90*,95*,100,110,120,125,130 | 115 | 297 | 300 | MT12 | 73.448 | 0.82 |
LM13 | ML12 | 11200 | 20000 | 2100 | 90*,95*,100*,110*,120*,125*,130,150,160 | 125 | 323 | 360 | MT13 | 103.86 | 1.672 |
LM14 | ML13 | 12500 | 25000 | 1900 | 100*,110*,120*,125*,130*,140*,150 160 | 135 | 333 | 400 | MT14 | 127.59 | 2.499 |
Note: 1. Mass and moment of inertia are approximate values calculated based on the material for cast steel, L recommendation, and minimum shaft hole. 2. The diameter of shaft hole with * can be used for Z-shaped shaft hole. 3.a and b are the hardness codes of the two elastic materials. |