The tapered barrel on these bushings is split on both sides, permitting them to contract more tightly around the shaft than quick-disconnect and taper-lock bushings. They’re for apply with split-tapered sprockets and pulleys of the same bushing design. As you tighten the included screws, the bushing grips the shaft and pulls it in to the sprocket or pulley.
This Split Taper Bushing was created exclusively for use with cast iron bushed bore pulleys and can be purchased on a single page as the pulley you will need. For use with 5/8” shaft sizes. Includes set screws. More Features: Manufactured from Steel For use with cast iron bushed bore pulley
Our stock metal Split Taper bushings feature wrench torque capability from 95 to 3,000 pounds and bore sizes from 3/8″ to 6-3/16″.
The split tapered bushing is a flanged bushing. Split tapered bushings are utilized on sheaves, pulleys, sprockets and equipment belt pulleys. The split tapered bushing alleviates the necessity to have a component bored to size, preferably lowering readily available requirements and allowing for changes in shaft size if important. The barrel of the split tapered bushing is normally split in two areas and can be keyed to the shaft. The barrel OD is also keyed to the drive component aswell. The advantage of the split tapered bushing is it will hold, even if the fasteners turn into loose. Split tapered bushings happen to be interchangeable between manufacturers.

Taper bushing are trusted as well as sprockets, v-belt pulleys, timing pulleys, coupling and other mechanical parts with taper bore connections.
Taper bushing series are constructed with high quality engineered components with great tolerance. The feature is easy to apply and needs no added alteration. These bushings can suit almost a myriad of assemblies and sizes. They will be the best choice in style for mechanical connections.
To complete designations add bore size. For instance: PD1215X16MM designates a 1215 taper bushing with a 16mm bore.
No costly re-boring: complete range of both metric and imperial offered.
Standard range matches up to 125mm/5″ shafts & Hub diameter required depends upon the application.
Complete brief reach range offered, for compact light assemblies & Clean, Compact Style.
Simple installation and removal.
This Split Taper Bushing was created exclusively for use with cast iron bushed bore pulleys and may be purchased on the same page as the pulley you need.
For use with 1 3/16” shaft sizes.
Includes 2 set screws.

Additional Features:
Made of Steel
For use with cast iron bushed bore pulley
This U1 Bushing with 5-1/2″ bore is a high-quality precision product that’s built for durability and strength. U1 bushings are used in an extensively wide variety of applications, including; sprockets, shaves, pulleys, gears, plus much more, we as well offer most of these goods. What pieces this bushing apart may be the high-quality steel structure along with exact manufacturing and high quality control; this ensures that you always get a premium quality regular product. What really pieces us in addition to the other fellas is our highly Split Taper Bushing china trained expert staff members and our company-wide objective of customer satisfaction.
1. Be sure the tapered cone floors of the bushing and the within of the driven product happen to be clean and free from anti-seize lubricants.
2. Place the bushing in sprocket or other part type that accepts the bushing.
3. Place cap screws loosely in pull-up holes. The bushing continues to be loose to make sure sliding suit on shaft.
4. With important on shaft, slide the sprocket or other portion type to the desired placement on the shaft. Make sure you keep the heads of the cap screws attainable.
5. Align the sprocket or component type, tighten the screws on the other hand and progressively until they are pulled up tight. Usually do not apply extensions on the wrench handles , nor allow the sprocket or part to become drawn i connection with flange of bushing. At this time there should be a gap between the bushing flange and sprocket, make sure this gap will not close.
Twice split barrel ensures concentricity
Grips the shaft with great clamp fit
High torque carrying capacity
Permits blind assembly
Load not carried or limited by mounting screws
External key on most sizes for confident drive and better torque carrying capabilities
Double-split barrel for positive clamping
Solid flange to maintain concentric bores
Available in inches, metric, and spline bores. Bore range from 3/8″ to 10″
Solid Flange & Dual Split Barrel – Assures better concentricity to the shaft.
Key to Key Travel – With keys upon both shaft and product to provide the strongest possible drive.
3/4″ per Foot Taper on Barrel – Self locking taper supplies the highest amount of mechanical locking merchandise to product.
The tapered barrel on these bushings is split on both sides, permitting them to contract more tightly around the shaft than quick-disconnect and taper-lock bushings. They’re for work with with split-tapered sprockets and pulleys of the same bushing design. As you tighten the included screws, the bushing grips the shaft and pulls it into the sprocket or pulley.
This Split Taper Bushing is designed exclusively for use with cast iron bushed bore pulleys and can be purchased on the same page as the pulley you will need. For apply with 5/8” shaft sizes. Includes set screws. Extra Features: Made of Steel For use with cast iron bushed bore pulley
Our stock steel Split Taper bushings feature wrench torque capacity from 95 to 3,000 pounds and bore sizes from 3/8″ to 6-3/16″.
The split tapered bushing is a flanged bushing. Split tapered bushings are utilized on sheaves, pulleys, sprockets and gear belt pulleys. The split tapered bushing alleviates the need to have an element bored to size, ideally lowering readily available requirements and enabling changes in shaft size if required. The barrel of the split tapered bushing can be split in two places and can be keyed to the shaft. The barrel OD is also keyed to the travel component aswell. The benefit of the split tapered bushing could it be will hold, even if the fasteners become loose. Split tapered bushings will be interchangeable between manufacturers.